On Dec 31, 7:52*pm, jim beam > wrote:
> On 12/31/2009 04:37 PM, Geo wrote:
>
>
>
>
>
> > I am about to remove crankshaft bolt but have conflicting procedures
> > from two different repair manuals on how to align the camshaft marks.
> > I'm hoping someone here has the knowledge to clarify. I have the
> > crankshaft pulley marks aligned, but I am not sure which of the
> > camshaft marks I am supposed to align. One set of instructions says to
> > make sure the rear camshaft pulley marks align and the other says to
> > make sure the front camshaft pulley marks align.
>
> > At present the crankshaft marks and the front camshaft marks only are
> > aligned. I notice that the valve positions on the rocker arm are not
> > all exaclty at the same height. When looking into the engine from the
> > front of the car the two on the upper right and ones on the lower left
> > are noticebly lower than the others. Doesn't look right to me. I want
> > to be 100% sure I have everything aligned properly before removing the
> > crank bolt.
>
> > Note: I need to remove the front cylinder head only if possible. I
> > think I remember reading somewhere that I cannot remove one cylinder
> > head at a time on this vehicle and that I have to remove both? Is this
> > true? Loks like they can be removed separately but maybe I'm missing
> > something.
>
> > Really hope someone can shed some light, any help would be much
> > appreciated.
>
> > Thanks in advance,
> > K
>
> the only reliable manual for this info is the honda manual - you don't
> mention what you have so my guess is that you googled here, saw the
> usual [but learned from experience] reactions to the haynes crap, then
> decided not to fess up to owning one.
>
> regarding heads, the usual reason for removing both is that you need to
> do the same clean-up on both. *to be sure the job's done right that is.
> * just like most people replace the water pump when doing a timing belt..
> * however, unless there is some mechanical gotcha like connected
> hardware, and provided there aren't any problems with your diagnosis as
> to why you only want to change one, you can remove just one head and
> you'll not notice any ill effects. *but if your diagnosis is not
> correct, you've just done a bunch of work that you'll have to do all
> over again. *why are you removing it? *what is the problem?- Hide quoted text -
>
> - Show quoted text -

Wow, quick response, thanks.

One of the manuals is Chilton and the other is a section cut from a
manual that someone posted in another Honda newsgroup but the name
eludes me at the moment, it's on another PC.

The vehicle is recently bought and has approximately 100,000m. The is
nothing wrong with the mechanics inside the head to the best of my
knowledge but I will soon find that out. One of the spark plug inserts
has been fused in the spark plug tube. I noticed the problem when
changing the plugs. When I tried to pull it out the insert the end
broke off using very little muscle. I tried to reach grabbing what was
left inside with pincers with all my might but it would not come out.
Maybe it has been leaking from the engine and became fused in place
(possible?) or someone broke it and glued it back which is also a
possibility.
I spoke with machine shop who said they can replace to spark plug tube
for...if not then, another cylinder head.

I plan on replacing the waterpump, timing belt while I'm at it but
really don't want to remove the other head.

I have successfully replaced a cylinder head in a four cylinder
vehicle before so I am not a complete stranger to doing this. I have
nothing to loose at this point except...my wife maybe since it's her
car. I absolutely can not afford to have it towed and worked on in a
garage. If I can't do this then it is junk to me.

Thanks,
K