A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto newsgroups » General
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

88 Volvo 240 front wheel bearings



 
 
Thread Tools Display Modes
  #1  
Old April 3rd 07, 10:07 PM posted to rec.autos.misc
kevo
external usenet poster
 
Posts: 2
Default 88 Volvo 240 front wheel bearings

Please let me know how to install front wheel bearings. I took the
inner and outter bearings out to replace and didn't have to use any
kind of tool whatsoever to remove them. I purchased new set of wheel
bearings from Les Schwab Tires. Installed them but did not install
the large, beveled metal ring that the bearings were packaged with.
Does this ring have to be installed?

Secondly, despite greasing them completely by hand, within 2 weeks of
installing them into the car, I began to hear bearing noise. I
recently removed the wheels again and on driver's side the lock nut
was unscrewed because the metal thing (can't think of the name) which
keeps the nut on, was broken off.

I would appreciate any advice on how to install these bearings. Do I
need a tool? What is the procedure?

Thank you,

Kevin


Ads
  #2  
Old April 4th 07, 08:26 PM posted to rec.autos.misc
Mike Walsh
external usenet poster
 
Posts: 101
Default 88 Volvo 240 front wheel bearings


The beveled metal ring is the bearing race and should be replaced because they are usually pitted when the bearing goes bad. The metal thing that keeps the nut on is a cotter pin and should not be reused. There should be a washer between the bearing and the nut that is keyed to the spindle and keeps the bearing from turning the nut.

kevo wrote:
>
> Please let me know how to install front wheel bearings. I took the
> inner and outter bearings out to replace and didn't have to use any
> kind of tool whatsoever to remove them. I purchased new set of wheel
> bearings from Les Schwab Tires. Installed them but did not install
> the large, beveled metal ring that the bearings were packaged with.
> Does this ring have to be installed?
>
> Secondly, despite greasing them completely by hand, within 2 weeks of
> installing them into the car, I began to hear bearing noise. I
> recently removed the wheels again and on driver's side the lock nut
> was unscrewed because the metal thing (can't think of the name) which
> keeps the nut on, was broken off.
>
> I would appreciate any advice on how to install these bearings. Do I
> need a tool? What is the procedure?
>
> Thank you,
>
> Kevin
>


--
Mike Walsh
West Palm Beach, Florida, U.S.A.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Dana 30 front wheel bearings KayakBill Jeep 20 July 9th 06 04:13 PM
front wheel bearings cj Dodge 2 November 22nd 05 04:30 AM
'97 Front Wheel Bearings krupnikas Ford Explorer 0 May 18th 05 04:01 PM
S series front wheel bearings private Saturn 2 April 3rd 05 09:15 PM
A4 - Front Wheel Bearings ? Graeme Audi 1 July 15th 04 12:47 PM


All times are GMT +1. The time now is 05:39 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.