If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Early series XJ front door hinge breakage tip
If you own an early (pre-Mopar, I think) XJ then you may have, if not
already, door hinges that have broken loose from the door frame. The cause is from the bean counters, most likely, saying the weld on the fourth side of the hinge ... the door opening side, was more expensive than seam sealer ... even thought the jig locating it probably would not have prevented welding ... wire and CO2 are just so expensive . . . . The bad part is they could have left holes in the body skin metal for the hinge mounts and welded to the heavier gauge "A" pillar substructure My 89 has that problem, soon to be welded back on, on the driver's door. Over a year ago, to slow down the breakage, I loosened the upper hinge from the door proper to gain room, drilled thru the hinge into the door frame with a bit sized for tapping 3/8" threads (5/16") then carefully drilled a clearance hole in the hinge only (I went with 7/16" for a bit of adjustment room). Then I ran a 3/8" NC tap into the holes drilled and cut threads but you could also run a dog point self-tap body bolt in as well. This "temporary" repair has held up in daily driving and some light off -roading until a month ago when the hinge finally broke off completely. But the bolt kept the door from coming loose enough to do damage to the other hinge or fall off completely, but I'll be welding up both hinges. -- Budd |
Ads |
#2
|
|||
|
|||
Early series XJ front door hinge breakage tip
Budd Cochran wrote:
> If you own an early (pre-Mopar, I think) XJ then you may have, if not > already, door hinges that have broken loose from the door frame. > > The cause is from the bean counters, most likely, saying the weld on the > fourth side of the hinge ... the door opening side, was more expensive > than seam sealer ... even thought the jig locating it probably would not > have prevented welding ... wire and CO2 are just so expensive . . . . > > The bad part is they could have left holes in the body skin metal for the > hinge mounts and welded to the heavier gauge "A" pillar substructure > > My 89 has that problem, soon to be welded back on, on the driver's door. > > Over a year ago, to slow down the breakage, I loosened the upper hinge > from the door proper to gain room, drilled thru the hinge into the door > frame with a bit sized for tapping 3/8" threads (5/16") then carefully > drilled a clearance hole in the hinge only (I went with 7/16" for a bit of > adjustment room). > > Then I ran a 3/8" NC tap into the holes drilled and cut threads but you > could also run a dog point self-tap body bolt in as well. > > This "temporary" repair has held up in daily driving and some light > off -roading until a month ago when the hinge finally broke off > completely. > > But the bolt kept the door from coming loose enough to do damage to the > other hinge or fall off completely, but I'll be welding up both hinges. > I guess I got lucky. My pre-MOPAR (88) MJ rolled down the drive when the parking brake cable snapped. Not too bad - it stopped about 6 feet up the neighbors driveway but... I had the hood up and the door open. The drivers side door caught the big tree at the end of my drive and got folded back far enough to bend the hinge strap. That's one hefty piece of steel! I had to heat it good and hot to bend it back and still didn't pop it loose from the frame. I could just see me trying to weld that sucker back with a gas rig and all that plastic/flamable crap so close but I lucked out. Used an 18" Cresent wrench for leverage and it bent back as perfectly. The new door fit like a charm. -- Will Honea |
#3
|
|||
|
|||
Early series XJ front door hinge breakage tip
"whonea" > wrote in message ... > Budd Cochran wrote: > >> If you own an early (pre-Mopar, I think) XJ then you may have, if not >> already, door hinges that have broken loose from the door frame. >> >> The cause is from the bean counters, most likely, saying the weld on the >> fourth side of the hinge ... the door opening side, was more expensive >> than seam sealer ... even thought the jig locating it probably would not >> have prevented welding ... wire and CO2 are just so expensive . . . . >> >> The bad part is they could have left holes in the body skin metal for the >> hinge mounts and welded to the heavier gauge "A" pillar substructure >> >> My 89 has that problem, soon to be welded back on, on the driver's door. >> >> Over a year ago, to slow down the breakage, I loosened the upper hinge >> from the door proper to gain room, drilled thru the hinge into the door >> frame with a bit sized for tapping 3/8" threads (5/16") then carefully >> drilled a clearance hole in the hinge only (I went with 7/16" for a bit >> of >> adjustment room). >> >> Then I ran a 3/8" NC tap into the holes drilled and cut threads but you >> could also run a dog point self-tap body bolt in as well. >> >> This "temporary" repair has held up in daily driving and some light >> off -roading until a month ago when the hinge finally broke off >> completely. >> >> But the bolt kept the door from coming loose enough to do damage to the >> other hinge or fall off completely, but I'll be welding up both hinges. >> > > I guess I got lucky. My pre-MOPAR (88) MJ rolled down the drive when the > parking brake cable snapped. Not too bad - it stopped about 6 feet up the > neighbors driveway but... I had the hood up and the door open. The > drivers > side door caught the big tree at the end of my drive and got folded back > far > enough to bend the hinge strap. That's one hefty piece of steel! I had > to > heat it good and hot to bend it back and still didn't pop it loose from > the > frame. I could just see me trying to weld that sucker back with a gas rig > and all that plastic/flamable crap so close but I lucked out. Used an 18" > Cresent wrench for leverage and it bent back as perfectly. The new door > fit > like a charm. > > -- > Will Honea Both the 88 and my 89 had the driver's door check strap broken, which may be a factor, but the 88 didn't have a hinge problem. Then it also it could be the welder at the plant didn't do a very good job either . . . My son and I are pulling the door Thursday and then welding everywhere we can reach with my genuine $90 Harbor Freight fluxcore wire welder To keep the sparks in check I'm duct taping sheet metal to the "A" pillar and door opening to deflect them away from flammables ... but we'll have the garden hose handy just in case. Budd |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
XJ Door Hinge Mounts | Grumman-581 | Jeep | 7 | May 16th 07 11:12 AM |
door hinge pin | Terry[_4_] | VW air cooled | 1 | March 30th 07 05:56 PM |
s10 door hinge spring | Bob Urz | Technology | 11 | March 19th 07 06:47 PM |
Separation of door panels above armrest on early 1990's 5 series | gnootso | BMW | 0 | September 15th 05 07:42 PM |
Door Hinge Question.... | Ervin Charles | VW air cooled | 1 | February 26th 05 12:49 AM |