If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Front Lug Nut/Stud Removal From '92 Accord
I snapped off a lug nut while rotating the tires on my '92 Accord-is
this a difficult job to put in a new stud? I really don't want to drive around on 3 lugs.This is the front pass. wheel. TIA! Doc |
Ads |
#2
|
|||
|
|||
Front Lug Nut/Stud Removal From '92 Accord
The Doctor > wrote in news:e99d7d9a-06b6-4509-80ed-
: > I snapped off a lug nut while rotating the tires on my '92 Accord-is > this a difficult job to put in a new stud? I really don't want to > drive around on 3 lugs.This is the front pass. wheel. TIA! > Doc > Sorry, but the entire hub needs to be pressed off the steering knuckle before the new stud can be installed. -- Tegger |
#3
|
|||
|
|||
Front Lug Nut/Stud Removal From '92 Accord
On 10/23/2010 10:38 AM, The Doctor wrote:
> I snapped off a lug nut while rotating the tires on my '92 Accord-is > this a difficult job to put in a new stud? I really don't want to > drive around on 3 lugs.This is the front pass. wheel. TIA! > Doc you can remove the hub bearing without a press on the accord [it unbolts from behind the knuckle] and drive in the new stud without any problems. all this said though, how did you break the stud? do you use a torque wrench? if not, you should. always. and i would probably recommend that if you're not into the torque wrench thing, that you have the stud replaced by someone that is - you don't want the knuckle assembly falling apart. -- nomina rutrum rutrum |
#4
|
|||
|
|||
Front Lug Nut/Stud Removal From '92 Accord
On 10/23/2010 12:00 PM, Tegger wrote:
> The > wrote in news:e99d7d9a-06b6-4509-80ed- > : > >> I snapped off a lug nut while rotating the tires on my '92 Accord-is >> this a difficult job to put in a new stud? I really don't want to >> drive around on 3 lugs.This is the front pass. wheel. TIA! >> Doc >> > > > Sorry, but the entire hub needs to be pressed off the steering knuckle > before the new stud can be installed. > don't need a press - the bearing assembly unbolts, so you can access the studs the same way as replacing the brake disk. -- nomina rutrum rutrum |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2002 Explorer lug nut stud & caliper bolt antisieze ? | HerkyJerky | Ford Explorer | 1 | June 19th 06 01:32 AM |
Lug nut stuck on lug - I'm up the creek. | Coasty | Dodge | 5 | December 13th 05 03:10 PM |
Lug nut stuck on lug - I'm up the creek. | Carolina Watercraft Works | Dodge | 0 | December 11th 05 07:51 PM |
Lug nut stuck on lug - I'm up the creek. | Helpful G | Dodge | 2 | December 9th 05 03:26 AM |
2005 Accord EX V6 16" Alloy Wheel-Lug Nut Torque Specification | BAS | Honda | 3 | July 20th 05 08:53 PM |