If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GPL and multiple controllers
On Jan 6, 3:43*am, Uwe Schürkamp > wrote:
> Problem is, while GPL sees the axes on both controllers fine, it only > responds to buttons on the first device (the cougar), but sees none of > the buttons on the g25 or its shifter (which is set to sequential mode > at the moment). > > I've tried using GPLShift, but that hasn't helped with the problem, > either. > > Also, GPL crashes on exit (BSOD on xp pro sp2, latest updates installed) > when I've taken to the track during the session (exits fine if I just > click around in the menus), both using the dx7 and opengl renderers. > Indexing is permitted on the gpl folder, is there anything else I could > try? Uwe, In GPLShift.ini, do you have the line Share_All_16_AXES = 1 near the bottom of the file? That should take care of it. In the Control Panel > Game Controllers window, does everything operate OK? Does the CTD ever happen while on-track? Are you running the 66 mod when it crashes on exit? You must set the Clutch_Shift_Sound = OFF for some reason. Other 66 mod problems and solutions can be found at http://forum.racesimcentral.com/showthread.php?t=307166 Otherwise a CTD can be caused by many things that are listed in the GPL FAQ at http://forum.racesimcentral.com/showthread.php?t=105748 It could even be related to your sound device, so one thing to try is reducing the hardware acceleration of the sound card. There have been problems with monitors not coping well with the change of res from in- car to the menus which are always at 640x480 res. Remco, From the GPL FAQ: GPL runs as only a small square in the top corner of the screen 1- The line in the core.ini: [ Direct3D7 ] DirectMirrorRendering = 1 Change it to DirectMirrorRendering = 0 |
Ads |
#2
|
|||
|
|||
GPL and multiple controllers
On Sun, 6 Jan 2008 06:51:10 -0800 (PST), Bob Simpson
> wrote: >Remco, From the GPL FAQ: > >GPL runs as only a small square in the top corner of the screen >1- The line in the core.ini: >[ Direct3D7 ] >DirectMirrorRendering =3D 1 >Change it to >DirectMirrorRendering =3D 0 Thanks Bob! Cheers! Remco |
#3
|
|||
|
|||
GPL and multiple controllers
On Jan 8, 4:29*am, Uwe Schürkamp > wrote:
> > Thanks, I'll check the FAQ. Is there a way to get GPL to run at > 1680x1050? This resolution is not listed in the renderer mode list. > > All the best, > > uwe The RastHacker can configure custom resolutions However,this one is so commonly asked for and since I did one up for myself, here's a link to an already made up one. http://forum.racesimcentral.com/show...2&postcount=73 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GPL and multiple controllers | Remco Moedt | Simulators | 0 | January 6th 08 10:06 AM |
Next fill-up, give thanks to Bush and his ZioNazi controllers | [email protected] | Driving | 5 | October 29th 07 11:47 PM |
98 GT Multiple ODB Codes | Bill P.[_1_] | Ford Mustang | 4 | November 4th 06 12:08 AM |
AWA [DEMAND] Glow plug controllers for the US | [email protected] | General | 0 | January 30th 06 03:03 PM |
Types of idle controllers/sensors? | Daniel VP | Technology | 3 | February 11th 05 05:14 PM |