If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Installing an MSD-6A in a 1972 Mustang
I'm installing an MSD-6A in a 1972 Ford Mustang, 351C-4V, manual
4-speed toploader. I need to connect the small red wire from the 6A to a +12V switched source (needs to be +12V at the run and start conditions of the ignition switch). Any recommendations as to where to tap in for this source? On the starter relay, there one of the small posts is +12V in the run, but I don't know if it is +12V in the start position. Thanks... |
Ads |
#2
|
|||
|
|||
"Joe" > wrote in message oups.com... > I'm installing an MSD-6A in a 1972 Ford Mustang, 351C-4V, manual > 4-speed toploader. I need to connect the small red wire from the 6A to > a +12V switched source (needs to be +12V at the run and start > conditions of the ignition switch). Any recommendations as to where to > tap in for this source? On the starter relay, there one of the small > posts is +12V in the run, but I don't know if it is +12V in the start > position. Why don't you run it directly to the ignition switch under the dash. Then there's no question if it's 12V or not. -- Scott W. '66 HCS Mustang 289 '68 Ranchero 500 302 '69 Mustang Sportsroof 351W ThunderSnake #57 http://home.comcast.net/~vanguard92/ |
#3
|
|||
|
|||
Joe wrote:
> I'm installing an MSD-6A in a 1972 Ford Mustang, 351C-4V, manual > 4-speed toploader. I need to connect the small red wire from the 6A to > a +12V switched source (needs to be +12V at the run and start > conditions of the ignition switch). Any recommendations as to where to > tap in for this source? On the starter relay, there one of the small > posts is +12V in the run, but I don't know if it is +12V in the start > position. > > Thanks... > There are a number of places under the dash to find a switched circuit. Start at the ignition switch. Ignition boxes require a fair amount of juice to operate, just take a look at the size of the red power lead. And 30 year old electrical wires are not all that sturdy. Use a 30A relay. -- ..boB 1997 HD FXDWG - Turbocharged! 2001 Dodge Dakota QC 5.9/4x4/3.92 1966 Mustang Coupe - Daily Driver 1965 FFR Cobra - Finally on the Road! |
#4
|
|||
|
|||
".boB" > wrote in message . com... > Joe wrote: >> I'm installing an MSD-6A in a 1972 Ford Mustang, 351C-4V, manual >> 4-speed toploader. I need to connect the small red wire from the 6A to >> a +12V switched source (needs to be +12V at the run and start >> conditions of the ignition switch). Any recommendations as to where to >> tap in for this source? On the starter relay, there one of the small >> posts is +12V in the run, but I don't know if it is +12V in the start >> position. >> >> Thanks... >> > There are a number of places under the dash to find a switched > circuit. Start at the ignition switch. > Ignition boxes require a fair amount of juice to operate, just take a > look at the size of the red power lead. And 30 year old electrical wires > are not all that sturdy. Use a 30A relay. > > -- > .boB Doesn't the large red wire go to a circuit that is hot all the time? The switched wire is small. Al |
#5
|
|||
|
|||
As I recall the large yellow wire under the dash is hot when key is on. On
my son's 72, I believe there is a 3 lug connector that you can tap into for accessories. Don't use the second small post on the starter solenoid. It's hot only when the solenoid is on. Otherwise, you're reading lower voltage fed back through the wire after it goes through the coil's ballast (resistance) wire. The second terminal is used to feed straight 12v to the coil for a hot spark on start. "Big Al" > wrote in message ... > > ".boB" > wrote in message > . com... >> Joe wrote: >>> I'm installing an MSD-6A in a 1972 Ford Mustang, 351C-4V, manual >>> 4-speed toploader. I need to connect the small red wire from the 6A to >>> a +12V switched source (needs to be +12V at the run and start >>> conditions of the ignition switch). Any recommendations as to where to >>> tap in for this source? On the starter relay, there one of the small >>> posts is +12V in the run, but I don't know if it is +12V in the start >>> position. >>> >>> Thanks... >>> >> There are a number of places under the dash to find a switched >> circuit. Start at the ignition switch. >> Ignition boxes require a fair amount of juice to operate, just take >> a look at the size of the red power lead. And 30 year old electrical >> wires are not all that sturdy. Use a 30A relay. >> >> -- >> .boB > > Doesn't the large red wire go to a circuit that is hot all the time? The > switched wire is small. > > Al > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Mustang Kicks GTO Butt | [email protected] | Ford Mustang | 14 | April 21st 05 01:34 AM |
2007 Shelby GT500 Mustang | Dan | Ford Mustang | 30 | March 25th 05 01:35 AM |
FORD TO INCREASE MUSTANG PRODUCTION TO MEET RUNAWAY CONSUMER DEMAND | Grover C. McCoury III | Ford Mustang | 1 | March 24th 05 12:08 AM |
Mustang Returns to Sports Car Racing | Grover C. McCoury III | Ford Mustang | 0 | January 29th 05 06:39 PM |
21st Century Goat vs Mustang Shootout | [email protected] | Ford Mustang | 1 | January 15th 05 07:09 PM |