A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » BMW
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

E39 / E60 Clutch sensitivity



 
 
Thread Tools Display Modes
  #1  
Old March 21st 07, 06:41 AM posted to alt.autos.bmw
BobP
external usenet poster
 
Posts: 15
Default E39 / E60 Clutch sensitivity

I've driven an E39 540i and an E60 545i and noticed that while the
clutch throw was fairly lengthy, the actual engagement zone was pretty
small, particularly on the E39. Is that just the nature of the beast
on these cars or did I bump into a couple funny ones? It's not a deal-
killer item, but is there any way to adjust the clutch to give me more
room to work with? The E39 in particular seemed to be
hypersensitive, with the engagement zone being at a point where the
clutch lever was "pushing back" harder than it did earlier in its
travel.

What say the FOAK?

Rancho Bob

Ads
  #2  
Old March 21st 07, 09:53 AM posted to alt.autos.bmw
[email protected]
external usenet poster
 
Posts: 664
Default E39 / E60 Clutch sensitivity

On 20 Mar 2007 22:41:29 -0700, "BobP" > wrote:

>I've driven an E39 540i and an E60 545i and noticed that while the
>clutch throw was fairly lengthy, the actual engagement zone was pretty
>small, particularly on the E39. Is that just the nature of the beast
>on these cars or did I bump into a couple funny ones? It's not a deal-
>killer item, but is there any way to adjust the clutch to give me more
>room to work with? The E39 in particular seemed to be
>hypersensitive, with the engagement zone being at a point where the
>clutch lever was "pushing back" harder than it did earlier in its
>travel.
>
>What say the FOAK?
>
>Rancho Bob



Look in any decent BMW mag' Long bolt with bit of stout rubber (shox mount) on
the end is now being sold to shorten the time taken for gear shifts.

Block of wood with Velcro under the clutch pedal would do the same.


Sir Hugh of Bognor

The difference between men and boys is the price of their toys.

Intelligence is not knowing the answer but knowing where and how to find it!

Hugh Gundersen

Bognor Regis, W.Sussex, England, UK
  #3  
Old March 21st 07, 10:55 AM posted to alt.autos.bmw
Fred W
external usenet poster
 
Posts: 326
Default E39 / E60 Clutch sensitivity

wrote:
> On 20 Mar 2007 22:41:29 -0700, "BobP" > wrote:
>
>
>>I've driven an E39 540i and an E60 545i and noticed that while the
>>clutch throw was fairly lengthy, the actual engagement zone was pretty
>>small, particularly on the E39. Is that just the nature of the beast
>>on these cars or did I bump into a couple funny ones? It's not a deal-
>>killer item, but is there any way to adjust the clutch to give me more
>>room to work with? The E39 in particular seemed to be
>>hypersensitive, with the engagement zone being at a point where the
>>clutch lever was "pushing back" harder than it did earlier in its
>>travel.
>>
>>What say the FOAK?
>>
>>Rancho Bob

>
>
>
> Look in any decent BMW mag' Long bolt with bit of stout rubber (shox mount) on
> the end is now being sold to shorten the time taken for gear shifts.
>


I don't think that would solve what the OP was complaining of. He's
saying (paraphrasing) that the point of clutch engagement is high up on
the pedal throw, and coincides with the "over-center" point of the pedal
spring, which makes it difficult to operate it smoothly.

The engagement point will sort of "self regulate" as the clutch disk
wears since it is hydraulically operated clutch. So, I don't think you
will be very successful in lowering the engagement point. You may be
able to play around with different pedal springs and the mechanism to
make it so the "over-center" occurs at a different place in the pedal throw.

Either that or, like most of these type of things, you'll probably get
used to it after driving it for a while. Think of the added benefit,
you'll be giving your left leg a daily workout... ;-)


--
-Fred W
  #4  
Old March 21st 07, 12:35 PM posted to alt.autos.bmw
John Carrier
external usenet poster
 
Posts: 216
Default E39 / E60 Clutch sensitivity


"BobP" > wrote in message
ups.com...
> I've driven an E39 540i and an E60 545i and noticed that while the
> clutch throw was fairly lengthy, the actual engagement zone was pretty
> small, particularly on the E39. Is that just the nature of the beast
> on these cars or did I bump into a couple funny ones? It's not a deal-
> killer item, but is there any way to adjust the clutch to give me more
> room to work with? The E39 in particular seemed to be
> hypersensitive, with the engagement zone being at a point where the
> clutch lever was "pushing back" harder than it did earlier in its
> travel.


Two things about the clutch

1) It's self-adjusting, not much you can do to change the engagement. You
can install a clutch stop that limits the pedal down-travel.

2) The clutch slave cylinder employs a clutch delay valve which prevents
rapid engagement of the clutch (BMW says to reduce drivetrain shock). It
makes smooth 1-2 shifts difficult to perform. It can be safely removed (or
if you're concerned about warrantee issues) replaced with a valve body whose
guts have been removed. Whichever method, the improvements are worthwhile.

3) As long as you're at it, you might try a short-shift kit. There are
several on the market which (some include a replacement selector rod, some
don't) which will replace the somewhat rubbery BMW shift mechanism with one
of surgical precision.

R / John

--------------------------------------------------------------------------------
I am using the free version of SPAMfighter for private users.
It has removed 451 spam emails to date.
Paying users do not have this message in their emails.
Try SPAMfighter for free now!


  #5  
Old March 21st 07, 04:27 PM posted to alt.autos.bmw
BobP
external usenet poster
 
Posts: 15
Default E39 / E60 Clutch sensitivity

On Mar 21, 1:55 am, Fred W > wrote:
> wrote:
> > On 20 Mar 2007 22:41:29 -0700, "BobP" > wrote:

>
> >>I've driven an E39 540i and an E60 545i and noticed that while the
> >>clutch throw was fairly lengthy, the actual engagement zone was pretty
> >>small, particularly on the E39. Is that just the nature of the beast
> >>on these cars or did I bump into a couple funny ones? It's not a deal-
> >>killer item, but is there any way to adjust the clutch to give me more
> >>room to work with? The E39 in particular seemed to be
> >>hypersensitive, with the engagement zone being at a point where the
> >>clutch lever was "pushing back" harder than it did earlier in its
> >>travel.

>
> >>What say the FOAK?

>
> >>Rancho Bob

>
> > Look in any decent BMW mag' Long bolt with bit of stout rubber (shox mount) on
> > the end is now being sold to shorten the time taken for gear shifts.

>
> I don't think that would solve what the OP was complaining of. He's
> saying (paraphrasing) that the point of clutch engagement is high up on
> the pedal throw, and coincides with the "over-center" point of the pedal
> spring, which makes it difficult to operate it smoothly.


Precisely.

> Either that or, like most of these type of things, you'll probably get
> used to it after driving it for a while. Think of the added benefit,
> you'll be giving your left leg a daily workout... ;-)


Yeah, but then I end up walking like Yosemite Sam, but only with one
bowed leg.... :-D

Rancho Bob

  #6  
Old March 21st 07, 06:01 PM posted to alt.autos.bmw
Pete[_2_]
external usenet poster
 
Posts: 160
Default E39 / E60 Clutch sensitivity

"John Carrier" wrote
> 2) The clutch slave cylinder employs a clutch delay valve which prevents
> rapid engagement of the clutch (BMW says to reduce drivetrain shock). It
> makes smooth 1-2 shifts difficult to perform. It can be safely removed
> (or if you're concerned about warrantee issues) replaced with a valve body
> whose guts have been removed. Whichever method, the improvements are
> worthwhile.


I had my CDV removed about 3 months ago (e39 530i), and honestly, smooth
shifting is still next to impossible on this car, mainly for the reason BobP
mentioned - the engagement point just seems extremely small. Either that,
or there is something wrong with my clutch (I bought it used with 30K
miles).

And it's not that I don't know how to drive stick. I drove sticks all my
life, and this is the first car where I can't execute smooth shifts majority
of the time.

Pete


  #7  
Old March 21st 07, 06:49 PM posted to alt.autos.bmw
Fred W
external usenet poster
 
Posts: 326
Default E39 / E60 Clutch sensitivity

BobP wrote:
> On Mar 21, 1:55 am, Fred W > wrote:
>
wrote:
>>
>>>On 20 Mar 2007 22:41:29 -0700, "BobP" > wrote:

>>
>>>>I've driven an E39 540i and an E60 545i and noticed that while the
>>>>clutch throw was fairly lengthy, the actual engagement zone was pretty
>>>>small, particularly on the E39. Is that just the nature of the beast
>>>>on these cars or did I bump into a couple funny ones? It's not a deal-
>>>>killer item, but is there any way to adjust the clutch to give me more
>>>>room to work with? The E39 in particular seemed to be
>>>>hypersensitive, with the engagement zone being at a point where the
>>>>clutch lever was "pushing back" harder than it did earlier in its
>>>>travel.

>>
>>>>What say the FOAK?

>>
>>>>Rancho Bob

>>
>>>Look in any decent BMW mag' Long bolt with bit of stout rubber (shox mount) on
>>>the end is now being sold to shorten the time taken for gear shifts.

>>
>>I don't think that would solve what the OP was complaining of. He's
>>saying (paraphrasing) that the point of clutch engagement is high up on
>>the pedal throw, and coincides with the "over-center" point of the pedal
>>spring, which makes it difficult to operate it smoothly.

>
>
> Precisely.
>
>
>>Either that or, like most of these type of things, you'll probably get
>>used to it after driving it for a while. Think of the added benefit,
>>you'll be giving your left leg a daily workout... ;-)

>
>
> Yeah, but then I end up walking like Yosemite Sam, but only with one
> bowed leg.... :-D
>
> Rancho Bob
>


That would be fitting for your usenet moniker, eh "Rancho"?

--
-Fred W
  #8  
Old March 21st 07, 07:52 PM posted to alt.autos.bmw
BobP
external usenet poster
 
Posts: 15
Default E39 / E60 Clutch sensitivity

On Mar 21, 10:49 am, Fred W > wrote:
> BobP wrote:
> > On Mar 21, 1:55 am, Fred W > wrote:

>
> wrote:

>
> >>>On 20 Mar 2007 22:41:29 -0700, "BobP" > wrote:

>
> >>>>I've driven an E39 540i and an E60 545i and noticed that while the
> >>>>clutch throw was fairly lengthy, the actual engagement zone was pretty
> >>>>small, particularly on the E39. Is that just the nature of the beast
> >>>>on these cars or did I bump into a couple funny ones? It's not a deal-
> >>>>killer item, but is there any way to adjust the clutch to give me more
> >>>>room to work with? The E39 in particular seemed to be
> >>>>hypersensitive, with the engagement zone being at a point where the
> >>>>clutch lever was "pushing back" harder than it did earlier in its
> >>>>travel.

>
> >>>>What say the FOAK?

>
> >>>>Rancho Bob

>
> >>>Look in any decent BMW mag' Long bolt with bit of stout rubber (shox mount) on
> >>>the end is now being sold to shorten the time taken for gear shifts.

>
> >>I don't think that would solve what the OP was complaining of. He's
> >>saying (paraphrasing) that the point of clutch engagement is high up on
> >>the pedal throw, and coincides with the "over-center" point of the pedal
> >>spring, which makes it difficult to operate it smoothly.

>
> > Precisely.

>
> >>Either that or, like most of these type of things, you'll probably get
> >>used to it after driving it for a while. Think of the added benefit,
> >>you'll be giving your left leg a daily workout... ;-)

>
> > Yeah, but then I end up walking like Yosemite Sam, but only with one
> > bowed leg.... :-D

>
> > Rancho Bob

>
> That would be fitting for your usenet moniker, eh "Rancho"?
>
> --
> -Fred W


Heh. Actually got that nick from a golf buddy of mine who liked that
I lived in Rancho Cucamonga for quite a few years. Ain't a lot of
cows out here to rustle anymore.

Though you can still smell them when wind blows wrong.

Rancho Bob

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Idle RPM sensitivity to signalling? Aaron407 Technology 16 April 21st 06 02:54 AM
1994 Ford Ranger Clutch slipping when hot- clutch has 1000 miles on it. RobertJohnC 4x4 1 November 25th 05 12:43 AM
What sensitivity/deadzone values to use with GTL Demo?? Cris Eichler Simulators 1 August 27th 05 07:18 PM
Power steering sensitivity. A4 Mike Holland Audi 1 December 8th 04 02:26 AM
Car Alarm Sensitivity Auscultans General 0 September 12th 04 12:40 AM


All times are GMT +1. The time now is 08:20 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.