If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
pto drive shaft to winch drive
i am having problems with an old koenig 100. the bolt securing the drive shaft
to the winch came off and the small shim which pits into the winch input shaft was lost (Alan bolt). I made a new shim out of old spring and it fits perfectly, however the 3/8 inset hex head bolt is not providing enough pressure and the winch still fails under a heavy load. I tried drilling a bit into that shim and also ground the bolt to fit into the depression and got a fair pull before the winch again failed. the rotation is starting to score the input shaft. I appreciate any ideas....any one ever just drill through the input shaft so the securing bolt fully penetrates the drive shaft.? I am amazed with the strength of the winch when operating normally and it is crazy that there is only a pressure hold and not a bolt all the way through the shaft....thanks for any ideas.... -- posted from http://www.motorsforum.com/jeep/pto-...ve-134992-.htm using MotorsForum's Web, Mobile and Social Media Interface to rec.autos.makers.jeep+willys and other automotive groups |
Ads |
#2
|
|||
|
|||
pto drive shaft to winch drive
I'm not familiar with your specific winch, but I've come across other
systems using a similar drive set up. The design has a purpose: to keep the winch from being overloaded ... a slip clutch setup, as it were, for your safety. I would suggest having the bolt hole drilled and tapped to the next larger thread size in a fine pitch (7/16" S.A.E. fine thread) and use that size Allen head ( your "inset hex head") or a Grade 8 Aircraft grade bolt. Do not let anyone sell you a stainless steel bolt as they will gall and stick in the threaded hole without anti-sieze and that would mean drilling and tapping out for an even larger bolt. Hope this healps. Budd "zane 79 landcruiser long body" > wrote in message roups.com... >i am having problems with an old koenig 100. the bolt securing the drive >shaft > to the winch came off and the small shim which pits into the winch input > shaft > was lost (Alan bolt). I made a new shim out of old spring and it fits > perfectly, however the 3/8 inset hex head bolt is not providing enough > pressure and the winch still fails under a heavy load. I tried drilling a > bit > into that shim and also ground the bolt to fit into the depression and got > a > fair pull before the winch again failed. the rotation is starting to score > the > input shaft. > I appreciate any ideas....any one ever just drill through the input shaft > so > the securing bolt fully penetrates the drive shaft.? I am amazed with the > strength of the winch when operating normally and it is crazy that there > is > only a pressure hold and not a bolt all the way through the > shaft....thanks > for any ideas.... > > -- > posted from > http://www.motorsforum.com/jeep/pto-...ve-134992-.htm > using MotorsForum's Web, Mobile and Social Media Interface to > rec.autos.makers.jeep+willys and other automotive groups > --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus |
#3
|
|||
|
|||
pto drive shaft to winch drive
|
#4
|
|||
|
|||
pto drive shaft to winch drive
replying to Budd Cochran, zane 79 landcruiser long body wrote:
thanks budd, got a good pull earlier, dragging a coconut tree out of the creek at my place here on the west coast of sumatra....i run a surf camp here....our motto is to protect and surf.....or surf and rescue when the beast, my 79 cruiser, is in a good mood. having the winch is essential i have pulled a lot of small truck out of dangerous situations.....btw I just ground down the 3/8 inch bolt to a flat face, my idea of drilling a small divot into the shim and tapering the end of the bolt was a bad idea. your suggestion helped me solve the problem.....thanks again....take care, zane -- posted from http://www.motorsforum.com/jeep/re-p...ve-134993-.htm |
#5
|
|||
|
|||
pto drive shaft to winch drive
"zane 79 landcruiser long body" > wrote in message oups.com... > replying to Budd Cochran, zane 79 landcruiser long body wrote: > thanks budd, got a good pull earlier, dragging a coconut tree out of the > creek > at my place here on the west coast of sumatra....i run a surf camp > here....our > motto is to protect and surf.....or surf and rescue when the beast, my 79 > cruiser, is in a good mood. having the winch is essential i have pulled a > lot > of small truck out of dangerous situations.....btw I just ground down the > 3/8 > inch bolt to a flat face, my idea of drilling a small divot into the shim > and > tapering the end of the bolt was a bad idea. your suggestion helped me > solve > the problem.....thanks again....take care, zane > > -- > posted from > http://www.motorsforum.com/jeep/re-p...ve-134993-.htm > Glad to help. I was a heavy equipment mechanic and journeyman millwright for ten years in an automotive muffler factory here in the States but I also served with the Indiana National Guard Combat Engineers in the 1970's. US Army 6X6 trucks used a similar overload unit on some winches and I remembered how were set up. Surf Safe!!!! Budd --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
94 EB 4x4 drive shaft | Paul | Ford Explorer | 2 | August 8th 05 08:11 PM |
TJ Drive shaft length | Morrissey | Jeep | 1 | May 18th 05 07:53 PM |
Drive shaft questions | HomeBrewer | Jeep | 1 | December 30th 04 03:24 PM |
A-4 drive shaft replacement | Rob Alward | Audi | 3 | November 15th 04 03:18 PM |