If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
The car is a 1995 Oldsmobile Cutlass with the 3.4L DOHC engine. The
negative battery cable terminal will not get very tight when attached to the battery. I can snug it up to where it just begins to get tight, but that is as much as I can get out of it. It feels as though there is not enough depth to the terminal threads going in to the battery. The other terminal tightens up normally and has no problems. The threads in the battery are fine. I have tried other batteries and have the same problem with the negative battery terminal.. Has anyone else ran across this issue before, and if so how did you fix the problem?. I am planning on replacing the whole cable, but would like to know if there is anything else I should try first. Thanks in advance for your help. |
#2
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
OK - I found that you can purchase terminal bolts in both standard and
extended lengths (see links below). How do you remove the old terminal bolt from the cable? What holds it in place? Standard bolt: http://tinyurl.com/5stfep Extended bolt: http://tinyurl.com/5rycdq Supplier's website: http://www.hifisoundconnection.com |
#3
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
On Jun 16, 7:46*am, KC > wrote:
> OK - I found that you can purchase terminal bolts in both standard and > extended lengths (see links below). How do you remove the old terminal > bolt from the cable? What holds it in place? > > Standard bolt:http://tinyurl.com/5stfep > Extended bolt:http://tinyurl.com/5rycdq > > Supplier's website:http://www.hifisoundconnection.com Just use a bolt and a nut! |
#4
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
maybe just get a flat washer and put it in there to fill the space.
|
#5
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
On Monday, June 16, 2008 at 3:10:43 AM UTC-10, hubcit wrote:
> maybe just get a flat washer and put it in there to fill the space. Make sure that the lead of the battery cable attaches to the battery face-to-face and any washer goes on the screw side, for best high current transfer at the lower auto voltage of 12.8 volts. |
#6
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
"KC" > wrote in message ... > OK - I found that you can purchase terminal bolts in both standard and > extended lengths (see links below). How do you remove the old terminal > bolt from the cable? What holds it in place? I've bought the replacement terminal bolts at auto parts stores, like Autozone. The old bolt will pull out of the terminal with a little elbow grease. Clean the innards of the cable well before putting it back together. GM side terminals can be a PITA when they get corroded |
#7
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
Would a battery terminal puller (like the one shown in the link below)
be of any use in extracting the terminal bolt from the battery cable? http://tinyurl.com/4n9zux |
#8
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
KC wrote:
> Would a battery terminal puller (like the one shown in the link below) > be of any use in extracting the terminal bolt from the battery cable? > > http://tinyurl.com/4n9zux > No, the bolt just muscles out past the rubber boot that is holding it in place. Not that hard to do. Maybe a pair of vise grips on the head might give you more leverage to pop it out or you could put a slit in the rubber with a razor blade to make it easier. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 'New' frame in the works for '08. Some Canadian Bush Trip and Build Photos: http://mikeromainjeeptrips.shutterfly.com |
#9
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
"HLS" > wrote in news:W8u5k.5666$89.5244
@nlpi069.nbdc.sbc.com: > GM side terminals can be a PITA when they get corroded > > What's the point of side-mount terminals? -- Tegger |
#10
|
|||
|
|||
Unable to Tighten GM Side Mount Battery Terminal
Was able to replace it. Thanks for the suggestions everyone.
I'd like to know the answer to Tegger's question, too. I've heard opinions about side terminals ranging from it was purely a money grab by GM to side mount connections seal the battery-to-cable connection better than top post connections. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Why you should remove the negative battery terminal before doing ANYTHING!!!! | Hachiroku $B%O%A%m%/(B | Technology | 57 | November 19th 07 04:05 PM |
Battery terminal short | Paul | Technology | 6 | July 10th 06 05:39 PM |
Battery terminal bolt replacement | [email protected] | Chrysler | 5 | June 15th 06 11:43 PM |
How to change the battery terminal | Jonelle H via CarKB.com | Ford Explorer | 1 | September 5th 05 01:13 PM |
Water on positive battery terminal? | Leon van Dommelen | Mazda | 13 | August 2nd 05 05:10 PM |