If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
starter Q?
Recently bought 88 f-250 4x4 diesel. needs a new starter.
could someone explain to me what the following descriptors of a starter are talking about: 12v, 13 tooth, 3.6kW, clockwise rotation, offset gear reduction. what do these terms mean when talking about a starter. thanks in advance for any help. biod -- Posted using the http://www.autoforumz.com interface, at author's request Articles individually checked for conformance to usenet standards Topic URL: http://www.autoforumz.com/4X4-starte...ict109910.html Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=514713 |
Ads |
#2
|
|||
|
|||
On 30 Mar 2005 00:26:43 -0500, 250biodiesel
> wrote: >Recently bought 88 f-250 4x4 diesel. needs a new starter. >could someone explain to me what the following descriptors of a >starter are talking about: >12v, Starter voltage. Can be 6V (old cars/trucks) 12 V newer cars trucks, or even 24 volts (usually big trucks and millitary vehicles >13 tooth, Number of teeth on the pinion gear. Must match the flywheel tooth pattern. >3.6kW, The power the starter has. 3.6 is a typical gas engine (V-8) starter, that will draw about 300 amps when cranking full load. >clockwise rotation, The direction of rotation. Some starters face backwards (are to the rear of teh flywheel) while some starters face forwards (are next to the oil pan, front of the flywheel) >offset gear reduction. Gear ruduction is used to allow the starter motor to run at a higher speed producing more power. Chrysler has used gear reduction staters for about 45 years at least. > >what do these terms mean when talking about a starter. Buy the right starter for your application. You don't need to consider any of the above--go to a parts store and ask for a starter for (describe your truck and engine) and they will fix you up. There is no such thing as a generic, fits all, starter! You need the right one, and then you don't have any choice in the above factors (except for a few aftermarket starters that may use gear reduction, such as Mean Green starters.) >thanks in advance for any help. >biod |
#3
|
|||
|
|||
just wondering are you planning on converting the diesel to burn used
vegetable oil? I was wondering due to you name |
#4
|
|||
|
|||
Up to 20% bio-diesel can be run in diesel engines without
modifications. Running more causes problems with hoses and seals, and may be harder on the injection pump. Bio diesel will 'dirty' up the fuel filter more often. Bio diesel has better lubricity over straight diesel. FWIW, I run B-20 in my Hummer. And I'm happy. On Wed, 30 Mar 2005 21:21:24 -0500, "be3805" > wrote: >just wondering are you planning on converting the diesel to burn used >vegetable oil? I was wondering due to you name |
#5
|
|||
|
|||
"Peter D. Hipson" wrote:
> Up to 20% bio-diesel can be run in diesel engines without > modifications. Running more causes problems with hoses and > seals, and > may be harder on the injection pump. Bio diesel will 'dirty' > up the > fuel filter more often. Bio diesel has better lubricity over > straight > diesel. > > FWIW, I run B-20 in my Hummer. And I'm happy. > > On Wed, 30 Mar 2005 21:21:24 -0500, "be3805" > > > wrote: > > >just wondering are you planning on converting the diesel to > burn used > >vegetable oil? I was wondering due to you name That is great you are running on B20, but I must correct you in that running biodiesel is dirtier for your vehicle and will cause more problems. That "dirt" is if you have ever run your engine on dino-fuel and the bio-d actually forces these "dead dino parts" to push through the system. Yes you will need to change fuel filters for quite some time after starting the bio-d program, but in the end (or is that out the end) choosing to run bio-d is a win-win for everyone. I plan on making bio-d in the garage. If you have a diesel look into 1. converting or 2. or making your own. If your of that persuasion. thanks for the answer to my starter q. Appreciated. Now I need to figure out how to get the top screw off of the starter so i can get it rebuilt. Screw is in a tight spot and I don’t have the right tool-or even know the right tool Any thoughts? thanks again. -- Posted using the http://www.autoforumz.com interface, at author's request Articles individually checked for conformance to usenet standards Topic URL: http://www.autoforumz.com/4X4-starte...ict109910.html Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=524126 |
#6
|
|||
|
|||
On 10 Apr 2005 20:54:12 -0400, 250biodiesel
> wrote: > >Now I need to figure out how to get the top screw off of the starter >so i can get it rebuilt. Screw is in a tight spot and I don’t have the >right tool-or even know the right tool I've always found that investing in tools pays off... SnapOn has some really interesting tools to do this type of work! (so does Mac, Kent-Moore, adn other serious (not Sears...) tool houses.) |
#7
|
|||
|
|||
yeh i agree snap o should have the tool you req or if not like our dealer he will get hold of one for you!! Not being funny but is it not easier and cheaper to get a recon unit??? -- Graham Wilkinson ------------------------------------------------------------------------ Graham Wilkinson's Profile: http://www.landyzone.co.uk/lz/member.php?userid=195 View this thread: http://www.landyzone.co.uk/lz/showthread.php?t=21938 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Starter problems, 350 to 400 turbo | flyboyf102 | Corvette | 3 | March 27th 05 06:52 PM |
91 Jetta: starter woes? | Rex Merriweather | VW water cooled | 0 | March 24th 05 05:22 AM |
the starter and neurtral safety swich are good | KingWalter | Technology | 12 | February 13th 05 09:29 AM |
88 civic starter problem? | Jeremy | Honda | 13 | November 3rd 04 06:40 PM |
Starter Troubleshooting | jls | Saturn | 1 | June 12th 04 11:59 PM |