A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » VW air cooled
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

HVX MODS on big-bore strokers



 
 
Thread Tools Display Modes
  #1  
Old June 18th 09, 09:56 PM posted to rec.autos.makers.vw.aircooled
Bob Hoover[_2_]
external usenet poster
 
Posts: 2
Default HVX MODS on big-bore strokers

To All:

Oil for the right-hand half of the crankcase arrives there via the
channel behind the #2 cam bearing. When building a high-reliability
engine a standard procedure is to increase the cross-sectional area of
that narrow channel.

While this improves things, the amount of oil that can reach the
rocker arms is severely limited. A modification to the tappets
improves that situation but only up to the amount of oil available.
To increase the amount of oil, one of the steps in the HVX mods is to
create a second oiling channel to the right-hand case half. This is
done by connecting the tappet oil gallery on the right-hand case-half
to another source of oil. This is done by connecting the tappet oil
gallery to the oil gallery behind the #3 bearing shell. This
procedure is illustrated in the FILE archives of this Group, and
consists of drilling two new oil passageways.

This procedure dates from the late 1960's. At that time the only
crankcases available were of German manufacture. Today, crankcases
come from Mexico and the quality is not as good as the German cases,
especially when it comes to performing the HVX modification. A
warning to check the case before drilling is included on the drawings.

Unfortunately, on Mexican crankcases the deep hole in the casting
where you need to extend the tappet gallery may be so deep that it is
impossible to perform the modification due to a lack of depth of
metal.

To say this another way, you can RUIN THE CRANKCASE if you fail to
ensure sufficient metal depth BEFORE doing any drilling.

There are various methods of repairing a crankcase that has been
damaged in this way but the only method suitable for a FLYING
Volkswagen involves welding. If you can not find a qualified weldor
to make the repair you should bite the bullet and buy a replacement
crankcase.

------------------------------------------------------

I mention this now because in the past week I have received TWO
messages from competent builders who have encountered crankcases that
could NOT receive the HVX modifications due to insufficient metal
depth. Both were Mexican crankcases, apparently of recent
manufacture.

A word to the wise should be sufficient. MEASURE before you drill or
you may find yourself with a junked crankcase on your hands.

-R.S.Hoover
Ads
  #2  
Old June 4th 18, 12:46 AM posted to rec.autos.makers.vw.aircooled
GreggHolmes
external usenet poster
 
Posts: 1
Default HVX MODS on big-bore strokers

https://youtu.be/NqrlqhiPC58
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Stroke vs Bore for a Given Displacement? [email protected] General 5 October 1st 06 12:58 AM
E39 bore wear problem. Dave Plowman (News) BMW 0 January 27th 06 11:44 PM
40 hp big bore P+C at Wofsburg West Lloyd McClelland VW air cooled 1 March 14th 05 05:27 PM
Wheel center-bore Grant Edwards Mazda 0 December 20th 04 09:32 PM


All times are GMT +1. The time now is 06:35 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004-2018 AutoBanter.
The comments are property of their posters.